0411 pcm pinout. LS Swap Standalone Wiring Harness 97-06 LS1 Drive-By-Cable w/ 4L60E Trans

The time now is AM. Not sure which one actually does the driving. Classified Buy - Sell - Trade - Wanted. To ensure the best experience, please keep your browser updated to the most current version. I'd suggest putting a piece of tape on them and labeling them C1 blue and C2 red. Fuel Level Sensor Signal.

 

I'm trying to gather information about all the PCM pins and differences in wiring of the PCM for different cars/trucks.Vehicle Speed Output Circuit K.

 

Looking for a spreadsheet to confirm pin locations between a 98 & PCM. We have cross referenced the two, but there are discrepancies.Page 1 of 2 1 2 Last Jump to page:.

 

staatenlos.online › _vortec_pcm.Not sure which one actually does the driving.

 

These are the RED & BLUE PCM connector pinouts that will cover to // Your harness MAY NOT have a pin in a location I have listed having.So you do is take the PCM pin you just removed, and insert it into the slot for pin 11 Go ahead and push it in all the way until the pin clicks into place.

 

Here are the PCM pinouts from AllData for both the l (was in my Blazer) and a Chevy Express Vortec.Otherwise, you can cause issues ranging from noise to those wires melting.Forum 0411 pcm pinout

 

I am using the current L pcm. There are about 9 differences in pinout points between the two pcms. Do i re-wire the pcm to match the express.I've altered these tunes as mentioned above, but they are just base tunes, you still need to modify them for your specific setup i.

 

staatenlos.online › pdf › LS1 PCM Pinouts.TCC Brake Switch.

 

LS1 PCM pinouts (Camaro, Firebird) Corvette similar. PCM connector (BLUE). Pin. Wire Color. Circuit. No. Function. 1. BLK. PCM Ground.Now lets look at the actual swap.

 

DIY PROM - ' PCM / VCM () Wiring Diagrams? - I could use some assistance locating (hopefully online) the PCM / VCM wiring diagrams for a My intentions are to flash my pcm for the Express van with the 5.

 

staatenlos.online › showthread › PCM-swap.Otherwise, you can cause issues ranging from noise to those wires melting.

 

Can you use any out of a V8 truck platform. Reason being, I have a surburban PCM but the pin out isn't perfect.Injector 2 Control.

 

The spreadsheet is organized by the wiring pinouts with the blackbox PCM pin # and the corresponding PCM pin #.Ignition Control 6.Forum 0411 pcm pinout

 

The wiring is slightly different between the 96, 97, and 98 to trucks. The PCM has a much faster processor than the Black Box PCM.PCM Battery Supply.

 

Below is a link to google docs, I am looking for anybody to help me cross reference and make sure I will not fry my newly tuned pcm.Ok, yesterday I replaced both of my O2 Sensors, I think my bank one sensor wire harness has a break in one of The leads between the PCM and the sensor.

 

I read about a spreadsheet for wiring. Lextech, Can I please bother you for the pcm spreadsheets on for a GMC Yukon GT, Vortec, 4L60E, 4wd.For more info about the o2 sensor differences click here.

 

a bit of corrosion one one plug, and some of the wires were brittle and cracked, but I used it with existing wiring so that didnt matter, just be sure to clean.You need to start with a Express van base tune.

 

LS/VORTEC Blue/Red ECM (Used) Current Performance Wiring. Why CPW? GM production ECM used in many / cars and trucks.Note: Removing all of these will result in a non-emissions friendly harness.

 

For use with GM or (Commonly known as ) PCM's. 5 pin MAF.Fuel Tank Pressure Sensor Ground.

 

mv p to volts up and down. could be possible I have made a wrong pinout change? I'm going to check the harness at the PCM (disconnected).Injector 2 Control.

 

Tuning, Diagnostics, Electronics, and Wiring - Does the PCM have Tow/Haul Capabilities? - Im looking to swap in the PCM and would also like to.EFI Connection does sell a custom harness that uses all the stock related components of the express van to get you fired up and going or you can build your own harness like I did using a 95 LT1 caprice harness trimmed for standalone using factory wiring diagrams for reference.

 

LS1 and LT1 Camaro wiring harnesses are very similar with the exception of a cam sensor and crank sensor. This “pick your salvage part” pcm uses a.The 5.

 

The CASE relearn shouldn't take more than a few minutes however you get it completed.

 

Otherwise, you can cause issues ranging from noise to those wires melting.

 

If you're having someone do the tuning for you, you may want to consider having them flash the tune in before you actually install the PCM i.

 

I went over my pinouts front to back, front to back many times, so I doubt that is the case.

 

Up at the top you can see the 2 80 pin connectors, below that is the 4 retainers 2 red, 2 blue.

 

Wire Color.